Roland VersaEXPRESS RF-640 User Manual Download Page 116

Page: 116 / 132

114

Other Problems

The Machine Doesn't Run

Is the cable connected?

Connect the cable securely.



"Setup Guide"

Is the power switched on?

Switch on the main power, then press the sub power switch and make sure the sub power switch lights up.



P. 20, "Switch On!"

Are the covers open?

Close Front Cover, Cover L and Cover R.

lit up?

Printing is not performed when

is not lit. Lower the loading lever.



P. 42, "Getting Ready to Receive Data from a Computer"

Is the top menu displayed?

Top menu

If the top menu isn't displayed, printing doesn't start even when data is sent from the computer. To go to the
top menu, press

, then press



P. 42, "Getting Ready to Receive Data from a Computer"

Is a message displayed on the screen?



P. 117, "A Message Appears"



P. 119, "An Error Message Appears"

lit up?

When

lights up, operation is paused. To resume, press

goes dark and printing

resumes.



P. 44, "Pausing and Canceling Printing"

㹕㸯㸰㸮㸮㹫㹫

Summary of Contents for VersaEXPRESS RF-640





































































































































Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands

Roland VersaEXPRESS RF-640, User Manual

Search results

Summary of Contents for VersaEXPRESS RF-640

Reviews:

Related manuals for VersaEXPRESS RF-640

Brands by name

Popular brands