178
Adding Effects
45: SERIAL DELAY
This delay connects two delay units in series. Feedback can be
applied independently to each delay unit, allowing you to produce
complex delay sounds.
fig.MFX-45
46: MODULATION DELAY
Adds modulation to the delayed sound.
When Feedback Mode is NORMAL:
fig.MFX-46a
When Feedback Mode is CROSS:
fig.MFX-46b
47: 3TAP PAN DELAY
Produces three delay sounds; center, left and right.
fig.MFX-47
Parameter
Value
Explanation
Delay1 Time
0–1300 ms, note
Delay time from when sound
is input to delay 1 until the de-
lay sound is heard
Delay1
Feedback #
-98– +98%
Proportion of the delay sound
that is to be returned to the in-
put of delay 1 (negative values
invert the phase)
Delay1 HF
Damp
200–8000 Hz,
BYPASS
Frequency at which the high-
frequency content of the de-
layed sound of delay 1 will be
cut (BYPASS: no cut)
Delay2 Time
0–1300 ms, note
Delay time from when sound
is input to delay 2 until the de-
lay sound is heard
Delay2
Feedback #
-98– +98%
Proportion of the delay sound
that is to be returned to the in-
put of delay 2 (negative values
invert the phase)
Delay2 HF
Damp
200–8000 Hz,
BYPASS
Frequency at which the high-
frequency content of the de-
layed sound of delay 2 will be
cut (BYPASS: no cut)
Pan #
L64–63R
Panning of the delay sound
Low Gain
-15– +15 dB
Amount of boost/cut for the
low-frequency range
High Gain
-15– +15 dB
Amount of boost/cut for the
high-frequency range
Balance #
D100:0W–D0:100W
Volume balance of the origi-
nal sound (D) and delay
sound (W)
Level
0–127
Output volume
R in
R out
L in
L out
Feedback 1
Pan L
Pan R
Delay 1
Feedback 2
Delay 2
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Delay
Delay
Modulation
Modulation
Parameter
Value
Explanation
Delay Left
0–1300 ms,
note
Adjusts the time until the delay sound
is heard.
Delay Right
Feedback
Mode
NORMAL,
CROSS
Selects the way in which delay sound is
fed back into the effect (See the figures
above.)
Feedback #
-98– +98 %
Adjusts the amount of the delay sound
that’s fed back into the effect. Negative
(-) settings invert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you don’t want to filter out any
high frequencies, set this parameter to
BYPASS.
Rate #
0.05–10.00 Hz,
note
Frequency of modulation
Depth
0–127
Depth of modulation
Phase
0-180 deg
Spatial spread of the sound
Low Gain
-15– +15 dB
Gain of the low frequency range
High Gain
-15– +15 dB
Gain of the high frequency range
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level
0–127
Output level
Parameter
Value
Explanation
Delay Left/
Right/Center
0–2600 ms,
note
Adjusts the time until the delay sound
is heard.
Center
Feedback #
-98– +98 %
Adjusts the amount of the delay sound
that’s fed back into the effect. Negative
(-) settings invert the phase.
HF Damp
200–8000 Hz,
BYPASS
Adjusts the frequency above which
sound fed back to the effect is filtered
out. If you do not want to filter out any
high frequencies, set this parameter to
BYPASS.
Left/Right/
Center Level
0–127
Volume of each delay
Low Gain
-15– +15 dB
Gain of the low frequency range
High Gain
-15– +15 dB
Gain of the high frequency range
Balance #
D100:0W–
D0:100W
Volume balance between the direct
sound (D) and the delay sound (W)
Level
0–127
Output level
R in
R out
L in
L out
Feedback
Feedback
Balance W
Balance D
Balance W
Balance D
2-Band
EQ
2-Band
EQ
Delay
Delay
Modulation
Modulation
L in
R in
L out
R out
Left Tap
Right Tap
Triple Tap Delay
2-Band
EQ
2-Band
EQ
Balance W
Balance D
Balance W
Balance D
Feedback
Center Tap
Fantom-Xa_e.book 178 ページ ２００４年１０月２２日 金曜日 午後２時３分
