Ricoh Aficio MP 161SPF Troubleshooting Manual Download Page 76

Page: 76 / 100

Adding Paper and Replacing Toner

Changing the Paper Size

This section describes how to change paper sizes.
Procedures for changing the paper size differ depending on the paper tray (Tray 1 or the option-
al paper tray unit). Make sure you are following the appropriate procedure before you begin.

Note

❒

Fan the paper before loading.

❒

Straighten curled or warped paper before loading.

Reference

For details about paper sizes and types, see “Tray Paper Settings”, General
Settings Guide.

Changing the Paper Size in the Paper Tray (Tray 1)

Use the following procedure when changing a paper size in the paper tray.

Make sure the paper tray is not in use.

Pull the paper tray out slowly until it stops.

Remove any remaining copy paper.

While pinching the release levers, pull the end fence off from the tray.

To load A4

size paper: place the end fence in the corner pocket on the left.

ARK011S

ARK012S

Summary of Contents for Aficio MP 161SPF





































































































Search results

Summary of Contents for Aficio MP 161SPF

Reviews:

Related manuals for Aficio MP 161SPF

Brands by name

Popular brands

Ricoh Aficio MP 161SPF, Troubleshooting Manual

Search results

Summary of Contents for Aficio MP 161SPF

Reviews:

Related manuals for Aficio MP 161SPF

Brands by name

Popular brands