682 Synergy Plus
88
Visit our website
12.6 Serial Port Setting Commands
The following commands can be used to configure serial port parameters.
12.6.1 Serial Ports
• Ports 1 and 2 are the two RS-232 ports
• Port 3 is the RS-485/422 port
• Port 4 and 5 are the two RS-232 or RS-485/422 ports on the optional Dual Serial Option Card
12.7 Ethernet and USB Setting Commands
The following commands can be used to configure Ethernet and USB parameters.
Table 12-6. Serial Port Commands
Command
Description
Values
EDP.TRIGGER#
p
Port serial input trigger function
CMD
(default), STRIND, STRLFT, REMOTE
EDP.BAUD#
p
Port baud rate
1200, 2400, 4800,
9600
(default), 19200, 28800, 38400, 57600, 115200
EDP.BITS#
p
Port data bits/parity
8NONE
(default), 8EVEN, 8ODD, 7EVEN, 7ODD
EDP.TERMIN#
p
Port line termination character
CR/LF
(default), CR
EDP.STOPBITS#
p
Port stop bits
1
(default), 2
EDP.ECHO#
p
Port echo
ON
(default), OFF
EDP.RESPONSE#
p
Port response
ON
(default), OFF
EDP.EOLDLY#
p
Port end-of-line delay
0–255 (0.1-second intervals),
0
(default)
EDP.ADDRESS#
p
Port RS-485 address (ports 3-5 only)
0–255,
0
(default)
EDP.DUPLEX#
p
Port duplex setting for RS-485 ports
(ports 3-5 only)
FULL
(default), HALF
EDP.TYPE#
p
Serial option card port type
(ports 4-5 only)
RS232
(default), RS485
For commands ending with
#p
, p is the port number (1-5)
Table 12-7. Ethernet TCP/IP and USB Commands
Command
Description
Values
WIRED.MACID
Ethernet hardware MAC ID (read only)
xx:xx:xx:xx:xx:xx
WIRED.DHCP
Enable Ethernet DHCP
ON
(default), OFF
WIRED.ENABLED
Enable wired Ethernet adapter
ON,
OFF
(default)
WIRED.IPADDR
Ethernet IP address
Valid IP xxx.xxx.xxx.xxx*,
0.0.0.0
(default)
WIRED.SUBNET
Ethernet subnet mask
Valid IP xxx.xxx.xxx.xxx*,
255.255.255.0
(default)
WIRED.GATEWAY
Ethernet gateway
Valid IP xxx.xxx.xxx.xxx*,
0.0.0.0
(default)
TCPC1.ECHO
TCP Client 1 echo
ON
(default), OFF
TCPC1.EOLDLY
TCP Client 1 end-of-line delay
0–255 (in 0.1 sec intervals),
0
(default)
TCPC1.IPADDR
TCP Client 1 remote server IP
Valid IP xxx.xxx.xxx.xxx*,
0.0.0.0
(default)
TCPC1.LINETERM
TCP Client 1 line termination
CR/LF
(default), CR
TCPC1.PORT
TCP Client 1 remote server port
1025–65535,
10001
(default)
TCPC1.RESPONSE
TCP Client 1 response
ON
(default), OFF
TCPC1.TRIGGER
TCP Client 1 input trigger type
CMD
(default), STRIND, STRLFT, REMOTE
TCPC1.DISCTIME
TCP Client 1 disconnect time (in seconds)
0–60 (0 = do not disconnect),
0
(default)
TCPS.PORT
TCP Server port number
1025–65535,
10001
(default)
TCPS.HOSTNAME
TCP Server host name
Up to 30 alphanumeric characters,
0
(default)
TCPS.TRIGGER
TCP Server input trigger type
CMD
(default), STRIND, STRLFT, REMOTE
TCPS.ECHO
TCP Server echo
ON
(default), OFF
TCPS.LINETERM
TCP Server line termination
CR/LF
(default), CR
TCPS.RESPONSE
TCP Server response
ON
(default), OFF
USB.TRIGGER
USB input trigger type
CMD
(default), STRIND, STRLFT, REMOTE
USB.LINETERM
USB line terminator
CR/LF
(default), CR
*
A valid IP consists of four numbers, in the range of 0 to 255, separated by a decimal point (127.0.0.1 and 192.165.0.230 are valid IP addresses)
Summary of Contents for REVOLUTION 682 Synergy Plus
Page 129: ......
