Translation of the Original Instruction Manual
Fig. 1 – 3
Fig. 4
Fig. 4
(1) Preparations
(2) Heating element
(3) Sleeve
(4) Heating spigot
(5) Heating socket
(6) Pipe
(7) Heating
(8) Completed joint
Fig. 5
Fig. 5
(1) Pipe outer diameter d
(2) Heat up
Heating element temperature
250 – 270°C
Heat-up time for SDR
(3) Switchover
Switchover time (maximum time)
(4/5) Cool down
Cool down time fi xed s
Cool down time total min
1)
SDR =
S
tandard
D
imension
R
atio ~
d/s. (ratio outer diameter/wall thickness)
EE
1 Supporting stand
2 Bench support
3 Handle
4 Heating element
5 Welding tools (heating socket)
6 Red power-on indicator lamp
7 Green temperat. indicator lamp
8 Temperature adjusting screw
FE
1 Supporting stand
2 Bench support
3 Handle
4 Heating element
5 Welding tools (heating socket)
6 Green power-on indicator lamp
7 Yellow temperature indicator lamp
General power tool safety warnings
WARNING
WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
with this power tool. Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool” in the warnings refers to your mains-operated (corded) power
tool or battery-operated (cordless) power tool.
1) Work area safety
a) Keep work area clean and well lit. Cluttered or dark areas invite accidents.
b) Do not operate power tools in explosive atmospheres, such as in the pres-
ence of fl ammable liquids, gases or dust. Power tools create sparks which
may ignite the dust or fumes.
c) Keep children and bystanders away while operating a power tool. Distrac-
tions can cause you to lose control.
2) Electrical safety
a) Power tool plugs must match the outlet. Never modify the plug in any way.
Do not use any adapter plugs with earthed (grounded) power tools. Unmodi-
fi ed plugs and matching outlets will reduce risk of electric shock.
b) Avoid body contact with earthed or grounded surfaces, such as pipes,
radiators, ranges and refrigerators. There is an increased risk of electric shock
if your body is earthed or grounded.
c) Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
d) Do not abuse the cord. Never use the cord for carrying, pulling or unplug-
ging the power tool. Keep cord away from heat, oil, sharp edges or moving
parts. Damaged or entangled cords increase the risk of electric shock.
e) When operating a power tool outdoors, use an extension cord suitable for
outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric
shock.
f) If operating a power tool in a damp location is unavoidable, use a residual
current device (RCD) protected supply. Use of an RCD reduces the risk of
electric shock.
3) Personal safety
a) Stay alert, watch what you are doing and use common sense when oper-
ating a power tool. Do not use a power tool while you are tired or under
the infl uence of drugs, alcohol or medication. A moment of inattention while
operating power tools may result in serious personal injury.
b) Use personal protective equipment. Always wear eye protection. Protec-
tive equipment such as a dust mask, non-skid safety shoes, hard hat or hearing
protection used for appropriate conditions will reduce personal injuries.
c) Prevent unintentional starting. Ensure the switch is in the off-position before
connecting to power source and/or battery pack, picking up or carrying the
tool. Carrying power tools with your fi nger on the switch or energising power
tools that have the switch on invites accidents.
d) Remove any adjusting key or wrench before turning the power tool on. A
wrench or a key left attached to a rotating part of the power tool may result in
personal injury.
e) Do not overreach. Keep proper footing and balance at all times. This enables
better control of the power tool in unexpected situations.
f) Dress properly. Do not wear loose clothing or jewellery. Keep your hair and
clothing away from moving parts. Loose clothes, jewellery or long hair can be
caught in moving parts.
g) If devices are provided for the connection of dust extraction and collec-
tion facilities, ensure these are connected and properly used. Use of dust
collection can reduce dust-related hazards.
h) Do not let familiarity gained from frequent use of tools allow you to become
complacent and ignore tool safety principles. A careless action can cause
severe injury within a fraction of a second.
4) Power tool use and care
a) Do not force the power tool. Use the correct power tool for your application.
The correct power tool will do the job better and safer at the rate for which it was
designed.
b) Do not use the power tool if the switch does not turn it on and off. Any power
tool that cannot be controlled with the switch is dangerous and must be repaired.
c) Disconnect the plug from the power source and/or remove the battery pack,
if detachable, from the power tool before making any adjustments, changing
accessories, or storing power tools. Such preventive safety measures reduce
the risk of starting the power tool accidentally.
d) Store idle power tools out of the reach of children and do not allow persons
unfamiliar with the power tool or these instructions to operate the power
tool. Power tools are dangerous in the hands of untrained users.
e) Maintain power tools and accessories. Check for misalignment or binding
of moving parts, breakage of parts and any other condition that may affect
the power tool’s operation. If damaged, have the power tool repaired before
use. Many accidents are caused by poorly maintained power tools.
f) Keep cutting tools sharp and clean. Properly maintained cutting tools with
sharp cutting edges are less likely to bind and are easier to control.
g) Use the power tool, accessories and tool bits etc. in accordance with these
instructions, taking into account the working conditions and the work to be
performed. Use of the power tool for operations different from those intended
could result in a hazardous situation.
h) Keep handles and grasping surfaces dry, clean and free from oil and grease.
Slippery handles and grasping surfaces do not allow for safe handling and control
of the tool in unexpected situations.
5) Service
a) Have your power tool serviced by a qualifi ed repair person using only
identical replacement parts. This will ensure that the safety of the power tool
is maintained.
Safety notes for heating element sleeve welding units
WARNING
WARNING
Read all safety warnings, instructions, illustrations and specifi cations provided
with this power tool. Failure to follow all instructions listed below may result in
electric shock, fi re and/or serious injury.
Save all warnings and instructions for future reference.
●
Do not use the power tool if it is damaged. There is a danger of accident.
●
Only connect the power tool of protection class I to a socket/extension lead
with a functioning PE conductor. There is a danger of electric shock.
●
Only touch the electrical device on the handle (3) when it is plugged into
an outlet. The heating element (4), the heating tools (5) as well as the metal
parts between the heating element and the plastic handle (3) reach operating
temperatures of up to 300°C. Touching these parts can cause severe burns.
●
Let the electrical device cool down for a long time after unplugging before
touching the metal parts. Touching parts that are still hot during the cooling
phase can cause severe burns. The electrical device takes a long time to cool
down after unplugging.
●
Protect third persons from hot power tool. Touching hot parts can cause
severe injury by burns.
●
Make sure that you keep your hands far enough away from the end of the
pipe, the moulding, the heating element (4) and the heating tools (5) or wear
suitable gloves when welding. The pipes and mouldings to be welded, the
heating element and the heating tools get hot during welding and can cause
severe burns. The weld connection stays very hot for a long time after completion.
●
Do not change the heating tools (5) until they have completely cooled down.
Touching parts which are still hot causes severe burns.
●
Protect third persons from the hot electrical device and hot welded connec-
tions. Touching the hot parts causes severe burns.
●
Do not accelerate the cooling process of the electrical device by immersing
it in liquid. There is a danger of injury from electric shock and/or sudden spurting
of the liquid. The electrical device could otherwise be damaged.
●
Place the electrical device down only on its supporting stand (1), in the
bench support (2) or on a fi re-retardant base. Placing the hot electrical device
on a base which is not fi re-retardant or in the vicinity of infl ammable material can
damage the surface and/or cause a fi re.
● Never let the power tool operate unattended. Switch off the power tool
during longer work breaks, pull out the mains plug. Electrical devices can
cause hazards which lead to material damage or injury when left unattended.
●
Only use approved and appropriately marked extension leads with a suffi -
cient cable cross-section. Use extension leads up to a length of 10 m with
cable cross-section 1.5 mm², from 10 – 30 m with cable cross-section 2.5 mm².
●
Check the power cable of the electrical device and the extension leads
regularly for damage. Have these renewed by qualifi ed experts or an authorised
REMS customer service workshop in case of damage.
●
Children and persons who, due to their physical, sensory or mental abilities
or lack of experience and knowledge are unable to operate the electrical
device safely may not use this electrical device without supervision or
instruction by a responsible person. Otherwise there is a risk of operating
errors and injuries.
eng eng
8
Summary of Contents for MSG 125 EE
Page 111: ...111...
