Rasilient PixelStor 5000 User Manual Download Page 142

Page: 142 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

7-105

Usage:

dahelp [Options]

Options:

-h/help: display this help page

[command]: display usage for the specified command

-s [pattern]: display usage for all the commands that match the pattern

Command List:

daacl - manage access control list

daaddrbk - add email address to notification list

dacomment - add comments to configuration

daconnstat - display connection statistics

dadate - display or set the date and time

dadg - manage disk groups

dadiskcache - Turn on/off disk write caches for all drives

dadiskload - download firmware for Seagate hard drives

dadsktst - measure disk baseline IO performance

dafwdwnld - download expander firmware

dahelp - display help information about commands

dahost - define or manage host

dahostname - display or set hostname for the storage array

dahwstat - display hardware status

dainspread - manage Inspection Read

daisns - manage iSNS client

dakem - display event log

dalun - manage the lun masking table

dantpdate - configure NTP server

dapasswd - set the password for the user

daphyinfo - get expander phy status information

dapm - configure the drive power management

dareboot - reboot local or remote controller

daroute - display or set gateway address

dasavelog - save the complete log file from the target to the local PC.

daselblk - select a chassis or a hard drive to blink

dasetup - set IP addresses, netmask, gateway and name server

dashutdown - shutdown local or remote controller

dasmartinfo - used to view disk smart information

dasnmp - Add/Delete SNMP managers to send traps to

dastat - display the system information

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands