Rasilient PixelStor 5000 User Manual Download Page 77

Page: 77 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

4-40

Figure 4-22 Convert Orphan Disk to Spare

Expanding a Disk Group

The ability to expand a Disk Group depends upon the number of drives and the type of RAID

used in the Disk Group and having enough spare drives to complete the expansion. Expanding

Disk Groups follows the same rules for each RAID type as when you created the Disk Group

(See Table 4-1 Disk Group Parameters ).

When expanding a RAID 5 DG, the expansion set will be appended to the original

set and the total size adjusted accordingly. The striping of the original RAID 5 set

will not be re-arranged.

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands