Rasilient PixelStor 5000 User Manual Download Page 131

Page: 131 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

7-94

7.6

Index of CLI Commands

The following table lists the PixelStor 5000 commands available through the command

line interface.

command

description

daacl

used to manage access control list

daaddrbk

used to add email address to notification list

dacomment

used to add comments to configuration

daconnstat

used to display connection statistics

dadate

used to display or set time and date

dadg

used to manage Disk Groups

dadiskload

download firmware for Seagate hard drives

dadsktst

measure disk baseline IO performance

dafwdwnld

used to download expander firmware

dahelp

used to display information about commands

dahost

used to define and manage host

dahostname

allows user to set the name of the storage array

dahwstat

used to display hardware status

dainspread

used to manage Inspection Read

daisns

used to manage isns registration

dakem

used to display the event log

dalun

used to manage the lun masking table

dantpdate

used to configure an NTP server

dapasswd

used to change the user password

daphyinfo

get expander phy status information

dapm

configure the drive power management

dareboot

used to reboot the local or remote controller

daroute

used to display or set the gateway address

dasavelog saves the log file to the /pub/ directory

daselblk

select a chassis or a hard drive to blink

dasetup

used to set IP addresses, netmask, gateway and

name server

dashutdown

used to shutdown the local or remote controller

dasmartinfo

used to view disk smart information

dasnmp

used to manage snmp groups

dastat

used to display system information

dastonith

used to forcibly reboot the remote controller

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands