Rasilient PixelStor 5000 User Manual Download Page 38

Page: 38 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

3-1

Hardware Preparation and Installation

This chapter describes the hardware setup procedures that you have to perform when installing

or removing system components. The PixelStor 5000 is designed with tool less modules which

allow users to remove or install modules without any tools. The tool less modules are listed

below:



Controller Modules



Controller Fan Board



Power Supply Modules



Fan Modules



Mid-plane



SATAII Hard Drive Modules

3.1

Make sure power is off

Before any installation or replacement, you must power off the storage completely. Follow the

steps below to power off the storage completely.

Moving the Power On/Off switch to the Off position does not completely remove

power from the system. Some portions of the power supply and some internal

circuitry remain active. Disconnect all power cords from the storage to completely

remove power from the system.

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands