Rasilient PixelStor 5000 User Manual Download Page 50

Page: 50 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

3-13

marked with a



icon on SAS IO module 0 of the 1st PixelStor 100e/312/324e.

3. For a dual controller configuration, follow the same exact process described above to

connect RAID controller 1 on the PixelStor 5000 to SAS IO module 1 on the 1

312e/100e. You have now properly connected the PixelStor 5000 RAID system to the

1st 300e expansion enclosure.

4. If you have additional 100e/312e/324e enclosures to add to this RAID system, follow the

rest of these steps to daisy chain them to the 1st 100e/312e/324e.

5. Connect one end of another of the included SAS cables to the SAS connector marked

with an



icon on the SAS IO module 0 of the 1st 100e/312e/324e expansion chassis.

Connect the other end of the SAS cable to the SAS connector marked with an



icon on

SAS IO module 0 of the 2nd 100e/312e/324e expansion enclosure.

6. Follow the same exact instructions above for connecting SAS IO module 1 on the 1st

300e expansion enclosure to SAS IO module 1 on the 2nd 300e expansion enclosure.

You have now properly connected a 2nd 100e/312e/324e expansion enclosure to the

first 300e enclosure.

7. To add additional 100e/312e/324e.expansion enclosures to this RAID array system,

repeat steps 5 and 6.

Figure 3-21 SAS Cable Connections

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands