Rasilient PixelStor 5000 User Manual Download Page 123

Page: 123 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

5-86



If the PixelStor Storage Manager indicates a faulty module, go to the system and look for

a module with a red Status Indicator. Replace the component (drive, fan, controller,

power supply). Once the faulty module is replaced, the System Health Alert will stop

flashing.



Check for missing slot covers. Module slot covers are required to ensure proper system

airflow. Replace missing slot covers to ensure temperature stays within specified system

limits.



If the PixelStor Storage Manager indicates a temperature fault and there are no faulty

system modules, check for a sudden rise or drop in the room temperature. If the room

temperature is beyond those listed in the system specifications section of this manual

(See System Specifications) shut down the system until you are able to correct the

problem.

5.2.12

Voltage Threshold Exceeded

The system is also equipped with voltage sensors. If any voltage sensor reading indicates an

abnormal value beyond the factory threshold, the System Health Alert is triggered.

Corrective action:



Check the Web-based console for the source of the problem.



Check Status Indicator on each power supply. Replace if faulty.



Ensure that the system is connected to an appropriate power source such as the rack’s
power distribution unit (PDU) or an uninterruptible power supply (UPS).

5.2.13

Fan Failure

Fan state and fan speed are also monitored. If a fan fails or if the fan speed falls below the

factory threshold, the System Health Alert is triggered.

Corrective Action:



Check the Web-based console for the source of the problem.



If the Power Supply fan has dropped below the recommended RPM that Power Supply

should be replaced.

5.2.14

List of Health Alert Notifications:

•

The other controller is down

•

RAM ECC error is detected

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands