Rasilient PixelStor 5000 User Manual Download Page 49

Page: 49 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

3-12

Figure 3-15 - PS 5000

Figure 3-16 100e/312e/324e SAS Connectors



SAS OUT - SFF-8470 Connector



SAS IN - SFF-8470 Connector

Figure 3-21 SAS Cable Connections - Shows the supported cabling configuration for PixelStor

5000 RAID system and 100e/312e/324e expansion enclosures. Start from the PixelStor 5000

chassis at the top of the diagram and connect to the first 100e/312e/324e enclosure below it.

Then add additional 100e/312e/324e enclosures.

____________________________________________________________________

Note in the single controller configuration only the bottom controller should be installed

and SAS cable connections should never be made between bottom and top controller.

The PixelStor 324e is a single controller only product should and should be connect as

such.

____________________________________________________________________

1. Each RAID controller on the PixelStor 5000 has a SAS connector marked with the



icon. Connect one end of one of the included SAS cables to SAS connector with



icon

on the PixelStor 5000.

2. Each IO module on the PixelStor 100e/312e/324e has 2 SAS connectors. One is

marked with a



icon (SAS OUT) and one is marked with a



icon (SAS IN). Connect

the other end of the SAS cable from Step 1 to the right-most module SAS connector



icon

SAS OUT always connects to



icon SAS IN.

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands