Rasilient PixelStor 5000 User Manual Download Page 158

Page: 158 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

7-121

Usage:

dastonith [-h/help] [0/1]

Options:

-h/help: print this help page.

1: set the stonith condition to the remote controller.

0: release the stonith condition to the remote controller.

Command Examples:

dastonith 1

dastonith 0

Notes:

To stonith the remote controller, issue the dastonith

commands in the following sequence.

dastonith 1

dastonith 0

The remote controller will reboot after you issue dastonith 0.

7.7.34

dasysalert

Use dasysalert to display system Health Alert setting or to change setting - enable or

disable. There are two components in the system Health Alert mechanism. Red LEDs

on the hard drives blink 3 times when there is a system Health Alert in the specific

chassis. Disabling system Health Alerts only turns off the blinking red LEDs and the red

Alert! Indication in the GUI. This command does not affect the health messages

viewable on the system health page or in the system logs.

dasysalert - turn on/off system alert

Usage:

dasysalert [-h] [on | off]

Options:

-h: help and print this page

-s/-show: the current status, 'on' or 'off'

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands