Rasilient PixelStor 5000 User Manual Download Page 48

Page: 48 / 161

Hardware Installation

PixelStor 5000 User Manual
Rev. 1, May 2013

3-11

To remove the mid-plane

Push both locking buttons in the direction of the arrow below.

Lift the mid-plane straight up from the chassis.

Figure 3-14 Removing the Mid-plane

3.4

Adding Expansion Enclosures (PixelStor 100e/312/324e)

The PixelStor 100e/312e/324e functions as an expansion enclosures for the PixelStor 5000

RAID system. Up to eight PixelStor 100e/312e

’s and up to four PixelStor 324e’s expansion

enclosures can be added to a PixelStor 5000 in a daisy chain fashion using the supplied SAS

IO cables to enable a maximum capacity of 108 drives. PixelStor 100e/312e/324e enclosures

can be added while the system is running (hot-added).

PixelStor 100e/312e are 2U/12 bay single or dual controller expansion enclosures while the

PixelStor 324e 4U/24 bay single controller only expansion enclosure.

The PixelStor 100e/312e/324e is designed with external SAS connectors to connect with the

PixelStor 5000 RAID system and to other 100e/312e/324e enclosures. These SAS connectors

can be used for upstream connection (subtractive routing) or downstream cascading (table

routing). Upstream and downstream connections are required to be connected to different SAS

connectors. Please see illustration below for details.

Summary of Contents for PixelStor 5000


































































































































































Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands

Rasilient PixelStor 5000, User Manual

Search results

Summary of Contents for PixelStor 5000

Reviews:

Related manuals for PixelStor 5000

Brands by name

Popular brands