![background image](http://html1.mh-extra.com/html/raleigh/ebike/ebike_user-manual_3522681027.webp)
26
I General User Manual
›
5. Undo the wheel nuts and put them to one side.
Remove the lock washers from the wheel axle.
›
6. Pull the rear wheel out of the dropout slits.
18.3 Removing the tyre and inner tube
›
Unscrew the valve cap, fastening nut and the cap
nut (if installed) from the valve. Remove the valve
insert from Dunlop or Woods valves.
›
Allow the remaining air to escape from the inner
tube.
›
Place the tyre lever on the inner edge of the tyre
opposite the valve.
›
Lever the tyre sidewall over the rim flange.
›
Push the second tyre lever between the rim and
tyre approx. 10 cm away from the first one.
›
Continue levering the tyre off the rim until the tyre
has detached round the entire circumference.
›
Take the inner tube out of the tyre.
18.4 Mending the inner tube
›
Pump up the inner tube.
›
Put the inner tube in a container filled with water
to locate the puncture.
›
Push the inner tube below the surface of the water.
Air bubbles will be visible at the point where the
inner tube is torn or perforated.
›
If you start losing air from the tyre on the road and
cannot find the hole, simply inflate the inner tube
hard. The hole will then get bigger as the air will
escape with greater force and you will be able to
hear more easily where it is coming from.
›
Allow the inner tube to dry.
›
Carefully roughen the inner tube in the area around
the puncture using the sandpaper.
›
Coat this area with rubber solution.
›
Wait for several minutes until the rubber solution
is touch dry.
›
Press the rubber patch firmly onto the damaged
area.
›
Leave the rubber patch to dry for several minutes.
›
2. Pull the outer casing out from the outer casing
holder of the cassette joint, and then remove the
inner cable from the slit in the bracket.
CJ-8S20
JAPAN
Bracket
Outer casing holder
Slit
1
2
1 Pull out from outer casing holder
2 Remove from the slit
›
3. Remove the inner cable fixing bolt unit from the
cassette joint pulley.
CJ-8S20
JAPAN
LOCK
Inner cable fixing bolt unit
Cassette joint pulley
If it is difficult to pull the outer casing out from the
outer casing holder of the cassette joint, insert a
2 mm Allen key or # 14 spoke into the hole in the
cassette joint pulley, and then turn the pulley to
loosen the inner cable. Then remove the inner ca-
ble fixing bolt unit from the pulley first, and after
this remove the outer casing from the outer casing
holder.
CJ-8S20
JAPAN
LOCK
Turn the
pulley
Pulley hole
2 mm Allen key
or # 14 spoke
Remove the inner
cable fixing bolt unit
Pull out from
the outer casing
holder
1
2
3
›
4. Undo the screw of the brake arm and remove it.
Summary of Contents for ebike
