![background image](http://html1.mh-extra.com/html/raleigh/ebike/ebike_user-manual_3522681168.webp)
V User Manual Impulse Pedelec
19
•
Display of journey time during the current trip
and the top speed reached on this trip.
•
The average speed during the current trip and
the total distance covered.
5.2.1 On/Off button
Press the button to switch the LCD control panel on and
off.
After switching on, the system is always in the display
mode in which you switched it off.
The following applies for bikes which are equipped with a
back-pedal brake:
The system will now perform a system check. “Please
move the pedals” will appear on the screen. If you set off
now the system will normally detect a pedal movement in
the “drive” and “back-pedal brake” directions. This com-
pletes the safety check, and you can ride as normal with
assistance.
If you cannot feel any assistance, simply back-pedal briefly
and then pedal forwards again to trigger the system check.
If there is still no assistance being delivered, the instruction
“Please move the pedals” will continue to be displayed. In
this case you should consult a specialist dealer.
5.2.2 Buttons for power-assist level
You can specify the power-assist level via the arrow but-
tons.
Each time you press an arrow button the power assist
changes by one level.
Each time you press the button with the arrow pointing
upwards, the assistance increases by one level from “no
assistance/stand by” through to the highest level:
POWER
.
Each time you press the button with the arrow pointing
downwards, the assistance decreases by one level from
POWER
through to the lowest assistance level “no assis-
tance/stand by”.
5.2.3 Display of the power-assist mode
The LCD display shows you how much assistance the
motor is currently providing.
Assist level
DISPLAY
ASSIST LEVEL
POWER
: This means the
assistance is working hard.
SPORT
: This means the
assistance is working with
a medium level of effort.
ECO
: This means the assis-
tance is only working with a
low level of effort.
STANDBY
: Battery indicator
still lights up (
)
5.2.4 Battery charge state indicator
The battery charge state display is located in the top
right-hand corner of the LCD display. Using a stylised bat-
tery divided into segments, it shows the charge remaining
in the battery.
DISPLAY
BATTERY CHARGE STATE
100 – 85.5%
85.5 – 71.5%
71.5 – 57.5%
57.5 – 42.4%
42.5 – 28.5%
28.5 – 14.5%
If the battery charge state falls below a minimum level,
the system switches off. Then the entire display fades and
goes off.
If you do not move your Pedelec for 10 minutes, the sys-
tem switches off automatically. If you subsequently want
to ride using the assistance, you will have to switch it
back on via the control panel.
Summary of Contents for ebike
