Quectel M10 At Command Set Download

Page: 136 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 135 -

6.2.34 AT+QIURC Enable Or Disable Initial URC Presentation

AT+QIURC Enable Or Disable Initial URC Presentation

Test Command

AT+QIURC=?

Response

+QIURC: (0,1)

Response

+QIURC:<mode>

Read Command

AT+QIURC?

Parameter

see Write Command

Response

ERROR

Write Command

AT+QIURC=

[<mode>]

Parameter

<mode>

0 disable URC presentation.

1 enable URC presentation

Reference

Note

When module power on and

initialization procedure is over .

URC “Call Ready” will be presented if <mode> is 1.

6.2.35 AT+QCSPWD Change PS Super Password

AT+QCSPWD Change PS Super Password

Response

ERROR

Write Command

AT+QCSPWD=

<oldpwd>,<newp

wd>

Parameters

<oldpwd>

string type.

Old password and length should be 8.

<newpwd>

string type.

New password and length should be 8.

Reference

Note

Default value of <oldpwd> is “12345678”.

If module is locked to a specific SIM card tCLCK and

password lost or SIM state is PH-SIM PUK, you can use the super

password to unlock it.

6.2.36 AT+QEXTUNSOL Enable /Disable Proprietary Unsolicited Indications

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands