Quectel M10 At Command Set Download Page 68

Page: 68 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 67 -

3.2.35 AT+CRLP Select Radio Link Protocol Parameter

AT+CRLP Select Radio Link Protocol Parameter

Response

TA returns values supported. RLP versions 0 and 1 share the same

parameter set. TA returns only one line for this set (where <ver

> is not

present).

+CRLP:

(list of supported <

iws

>s), (list of supported <

mws

>s), (list of

supported <

>s), (list of supported <

ver1

>s),

(list of supported <

>s)

Test Command

AT+CRLP=?

Parameters

see Write Command

Response

TA returns current settings for RLP version. RLP versions 0 and 1 share

the same parameter set. TA returns only one line for this set (where

<ver

> is not present).

+CRLP: <iws>,<mws>,<T1>,<N2>,<ver1>,<T4>

Read Command

AT+CRLP?

Parameters

see Write Command

Response

TA sets radio link protocol (RLP) parameters used when non-transparent

data calls are setup.

Write Command

AT+CRLP=[<iws

>[,<mws>[,<T1>[

,<N2>[,<ver>[,<T

4>]]]]]]

Parameters

<iws>

0-61

Interworking window size (IWF to MS)

<mws>

0-61

Mobile window size(MS to IWF)

<T1>

39-255

acknowledgment timer T1 in 10 ms units

<N2>

1-255

retransmission attempts N2

<verx>

RLP version number in integer format; when

Version indication is not present it shall equal 0.

<T4>

3-255

re-sequencing period in integer format, in units

of 10 ms.

Reference

GSM 07.07 [13]

Note

3.2.36 AT+CRSM Restricted SIM Access

AT+CRSM Restricted SIM Access

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Quectel M10, At Command Set, Page: 68 / 165

Search results

Summary of Contents for M10

Reviews: