Quectel M10 At Command Set Download Page 74

Page: 74 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 73 -

3.2.44 AT+CMUX Multiplexer Control

AT+CMUX Multiplexer Control

Response

+CMUX:

list of supported (<

mode

>s),(<

subset

>s),(<

port_spe

>s),(<

>s)

Test Command

AT+CMUX=?

Parameters

See Write Command

Response

+CME ERROR: <err>

Write Command

AT+CMUX=[<m

ode>[,<subset>[,

<port_speed>[,<

N1>[,<T1>[,<N2

>[,<T2>[,<T3>[,<

k>]]]]]]]]]

Parameters

<mode>

multiplexer transparency mechanism

0 Basic

option

<subset>

the way in which the multiplexer control channel is set up

0 UIH frames used only

<port_speed>

transmission rate

5 115200bit/s

<N1>

maximum frame size

127

<T1>

acknowledgement timer in units of ten milliseconds

<N2>

maximum number of re-transmissions

<T2>

response timer for the multiplexer control channel in units of

ten milliseconds

<T3>

wake up response timers in seconds

<k>

window size, for Advanced operation with Error Recovery

options

Read Command

AT+CMUX ?

Response:

+CMUX: (mode-1),0,5,127,10,3,30,10,2

ERROR

Reference

GSM 07.07 [13]

Note

1. Advanced option with Error Recovery options is not supported.

2. The multiplexing transmission rate is according to the current serial

baud rate. It is recommended to enable multiplexing protocol under

115200 bit/s baud rate

3. Multiplexer control channels are listed as follows:

Channel Number

Type

DLCI

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Brands by name

Popular brands