manualshive.com logo in svg

Quectel M10, At Command Set, Page: 24 / 165

Share
Download
Quectel M10 At Command Set Download Page 24

M10 AT Commands Set                                                                                       

 

M10_ATC_V1.01 

 

- 23 - 

V.25ter 

z

 

Default 10 = LF. 

 

2.2.18 ATS5 Set Command Line Editing Character 

ATS5 Set Command line editing character 

Read Command 

ATS5? 

Response 

<n>  

 

OK 

Response 

This parameter setting determines the character recognized by TA as a 

request to delete from the Command line the immediately preceding 

character. 

OK 

Write Command 

ATS5=<n>

 

Parameter 

<n>

             0-8-127 

response formatting character 

 

Reference 

V.25ter 

Note 

z

 

Default 8 = Backspace. 

 

2.2.19 ATS6 Set Pause Before Blind Dialing 

ATS6 Set Pause Before Blind Dialing 

Read Command 

ATS6? 

Response 

<n>  

 

OK 

Response 

OK 

Write Command 

ATS6=<n>

 

Parameter 

<n>

             0-2-10 number of seconds to wait before blind dialing 

Reference 

V.25ter 

Note 

z

 

No effect for GSM 

 

2.2.20 ATS7 Set Number Of Seconds To Wait For Connection Completion 

ATS7 Set Number Of Seconds To Wait For Connection Completion 

Read Command 

ATS7? 

Response 

<n>  

 

OK 

Response 

This parameter setting determines the amount of time to wait for the 

connection completion in case of answering or originating a call.

 

OK 

Write Command 

ATS7=<n>

 

Parameter 

Quectel

Summary of Contents for M10






































































































































































Reviews:

No comments