Quectel M10 At Command Set Download Page 144

Page: 144 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 143 -

Parameters

See Write Command

Write Command

AT+QIREGAPP

=<apn>,<user

name>,<

password>[,<rat

e>]

Response

ERROR

Parameters

<apn>

a string parameter which indicates the GPRS access point

name or the call number of CSD

<user name>

a string parameter which indicates the GPRS/CSD user name

<password>

a string parameter which indicates the GPRS/CSD password

<rate>

the speed of data transmit for CSD

Execution

Command

AT+QIREGAPP

Response

ERROR

Reference

Note

1 The write command and execution command of this command is valid

only at the state of IP INITIAL. After operating this command, the state will

be changed to IP START.

2 the value of QICSGP (please refer to AT+QICSGP) define what kind of

bearer (GPRS or CSD) the parameters are used for.

7.2.7 AT+QIACT Bring Up Wireless Connection With GPRS Or CSD

AT+QIACT Bring Up Wireless Connection With GPRS Or CSD

Execution

Command

AT+QIACT

Response

ERROR

Reference

Note

AT+QIACT only activates GPRS/CSD context at the status of IP START

，

after operating this Command, the state will be changed to IP CONFIG. If

module accepts the activated operation, the state will be changed to IP IND;

after module accepting the activated operation, if activate successfully, the

state will be changed to IP GPRSACT, response OK, otherwise response

ERROR.

7.2.8 AT+QILOCIP Get Local IP Address

AT+QILOCIP Get Local IP Address

Read Command

AT+QILOCIP?

Response

Execution Response

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Brands by name

Popular brands