Quectel M10 At Command Set Download Page 5

Page: 5 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 4 -

3.2.19 AT+CLCK Facility Lock..................................................................................................... 51

3.2.20 AT+CLIP Calling Line Identification Presentation ............................................................. 52

3.2.21 AT+CLIR Calling Line Identification Restriction ............................................................... 53

3.2.22 AT+CMEE Report Mobile Equipment Error....................................................................... 54

3.2.23 AT+COLP Connected Line Identification Presentation....................................................... 55

3.2.24 AT+COPS Operator Selection ............................................................................................. 56

3.2.25 AT+CPAS Mobile Equipment Activity Status ..................................................................... 58

3.2.26 AT+CPBF Find Phonebook Entries..................................................................................... 58

3.2.27 AT+CPBR Read Current Phonebook Entries ...................................................................... 59

3.2.28 AT+CPBS Select Phonebook Memory Storage................................................................... 60

3.2.29 AT+CPBW Write Phonebook Entry .................................................................................... 61

3.2.30 AT+CPIN Enter PIN............................................................................................................ 62

3.2.31 AT+CPWD Change Password ............................................................................................. 62

3.2.32 AT+CR Service Reporting Control...................................................................................... 64

3.2.33 AT+CRC Set Cellular Result Codes For Incoming Call Indication..................................... 64

3.2.34 AT+CREG Network Registration........................................................................................ 65

3.2.35 AT+CRLP Select Radio Link Protocol Parameter............................................................... 67

3.2.36 AT+CRSM Restricted SIM Access...................................................................................... 67

3.2.37 AT+CSQ Signal Quality Report .......................................................................................... 68

3.2.38 AT+FCLASS FAX: Select, Read Or Test Service Class..................................................... 69

3.2.39 AT+FMI FAX: Report Manufactured ID............................................................................. 69

3.2.40 AT+FMM FAX: Rreport Mmodel ID .................................................................................. 70

3.2.41 AT+FMR FAX: Report Revision ID.................................................................................... 70

3.2.42 AT+VTD Tone Duration...................................................................................................... 71

3.2.43 AT+VTS DTMF And Tone Generation ............................................................................... 71

3.2.44 AT+CMUX Multiplexer Control ......................................................................................... 73

3.2.45 AT+CNUM Subscriber Number .......................................................................................... 74

3.2.46 AT+CPOL Preferred Operator List...................................................................................... 74

3.2.47 AT+COPN Read Operator Names ....................................................................................... 75

3.2.48 AT+CFUN Set Phone Functionality. ................................................................................... 76

3.2.49 AT+CCLK Clock................................................................................................................. 76

3.2.50 AT+CSIM Generic SIM Access .......................................................................................... 78

3.2.51 AT+CALM Alert Sound Mode ............................................................................................ 78

3.2.52 AT+CRSL Ringer Sound Levels ......................................................................................... 79

3.2.53 AT+CLVL Loud Speaker Volume Level.............................................................................. 79

3.2.54 AT+CMUT Mute Control.................................................................................................... 80

3.2.55 AT+CPUC Price Per Unit And Currency Table................................................................... 81

3.2.56 AT+CCWE Call Meter Maximum Event ............................................................................ 81

3.2.57 AT+CBC Battery Charge..................................................................................................... 82

3.2.58 AT+CUSD Unstructured Supplementary Service Data ....................................................... 83

3.2.59 AT+CSSN Supplementary Services Notification ................................................................ 83

3.2.60 AT+CSNS Single Numbering Scheme ................................................................................ 84

3.2.61 AT+CMOD Configure Alternating Mode Calls .................................................................. 85

4 AT Commands According to GSM07.05

........................................................................................ 86

4.1 Overview of AT Commands According to GSM07.05 ................................................................. 86

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Quectel M10, At Command Set, Page: 5 / 165

Search results

Summary of Contents for M10

Reviews: