Quectel M10 At Command Set Download Page 28

Page: 28 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 27 -

Parameter

<value>

DCD

line is always ON

DCD

line is ON only in the presence of data carrier

Reference

V.25ter

Note

2.2.28 AT&D Set DTR Function Mode

AT&D Set DTR Function Mode

Response

This parameter determines how the TA responds when circuit 108/2(DTR)

is changed from the ON to the OFF condition during data mode.

Execution

Command

AT&D[<value>]

Parameter

<value>

TA ignores status on DTR

ON->OFF on DTR: Change to Command mode with

remaining the connected call

2 ON->OFF on DTR: Disconnect call, change to

Command mode. During state DTR = OFF is auto-answer off.

Reference

V.25ter

Note

2.2.29 AT&F Set All Current Parameters To Manufacturer Defaults

AT&F Set All Current Parameters To Manufacturer Defaults

Response

TA sets all current parameters to the manufacturer defined profile.

Execution

Command

AT&F[<value>]

Parameter

<value>

set all TA parameters to manufacturer defaults.

Reference

V.25ter

Note

2.2.30 AT&V Display Current Configuration

AT&V Display Current Configuration

Response

TA returns the current parameter setting.

Execution

Command

AT&V[<n>]

Parameter

<n>

0 profile

number

Reference

V.25ter

Note

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands