Quectel M10 At Command Set Download Page 35

Page: 35 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 34 -

<value>

0 Disables reporting of local port rate

Enables reporting of local port rate

Reference

V.25ter

Note

If the

value

is set to 1, the following intermediate result will comes

out on connection to indicates the port rate settings

+ILRR:<rate>

<rate>

port rate setting on call connection in Baud per second

300

1200

2400

4800

9600

14400

19200

28800

38400

57600

115200

2.2.43 AT+IPR Set TE-TA Fixed Local Rate

AT+IPR Set TE-TA Fixed Local Rate

Response

+IPR:

(list of supported auto detectable <

rate

>s),(list of supported

fixed-only<

rate

>s)

Test Command

AT+IPR=?

Parameter

See Write Command.

Response

+IPR: <rate>

Read Command

AT+IPR?

Parameter

See Write Command.

Response

This parameter setting determines the data rate of the TA on the serial

interface. The rate of Command takes effect following the issuance of any

result code associated with the current Command line.

Write Command

AT+IPR=<rate>

Parameter

<rate>

Baud rate per second

0(Autobauding ,see chapter 2.2.45.1 )

150

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands