Quectel M10 At Command Set Download Page 63

Page: 63 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 62 -

3.2.30 AT+CPIN Enter PIN

AT+CPIN Enter PIN

Test Command

AT+CPIN=?

Response

Parameter

see Write Command

Response

TA returns an alphanumeric string indicating whether some password is

required or not.

+CPIN: <code>

Read Command

AT+CPIN?

Parameter

<code>

READY

no further entry needed

SIM PIN

ME is waiting for SIM PIN

SIM PUK

ME is waiting for SIM PUK

PH_SIM PIN ME is waiting for phone to SIM card (antitheft)

PH_SIM PUK ME is waiting for SIM PUK (antitheft)

SIM PIN2

PIN2, e.g. for editing the FDN book possible only

if preceding Command was acknowledged with +CME ERROR:17

SIM PUK2

possible only if preceding Command was acknowledged

with error +CME ERROR: 18.

Response

TA stores a password which is necessary before it can be operated (SIM

PIN, SIM PUK, PH-SIM PIN, etc.). If the PIN is to be entered twice, the TA

shall automatically repeat the PIN. If no PIN request is pending, no action is

taken and an error message, +CME ERROR, is returned to TE.

If the PIN required is SIM PUK or SIM PUK2, the second pin is required.

This second pin, <new pin>, is used to replace the old pin in the SIM.

Write Command

AT+CPIN=<pin>

[, <new pin>]

Parameters

<pin>

string type; password

<new pin>

string type; If the PIN required is SIM PUK or SIMPUK2:

new password

Reference

GSM 07.07 [13]

Note

3.2.31 AT+CPWD Change Password

AT+CPWD Change Password

Test Command

AT+CPWD=?

Response

TA returns a list of pairs which present the available facilities and the

maximum length of their password.

+CPWD:

(list of supported <

fac

>s, <

pwdlength

>s)

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands