Quectel M10 At Command Set Download Page 112

Page: 112 / 165

M10 AT Commands Set

M10_ATC_V1.01

- 111 -

<cid>

a numeric parameter which specifies a particular PDP

context definition (see +CGDCONT Command)

Reference

GSM07.07

Note

5.2.7 AT+CGPADDR Show PDP Address

AT+CGPADDR Show PDP Address

Test Command

AT+CGPADDR=

Response

+CGPADDR:

(list of defined <

cid

>s)

Parameter

See Write Command

Write Command

AT+CGPADDR=

<cid>

Response

+CGPADDR: <cid>,<PDP_addr>

ERROR

Parameters

<cid>

a numeric parameter which specifies a particular PDP

context definition (see +CGDCONT Command)

<PDP_addr>

a string that identifies the MT in the address space

applicable to the PDP. The address may be static or

dynamic. For a static address, it will be the one set by the

+CGDCONT Command when the context was defined. For

a dynamic address it will be the one assigned during the last

PDP context activation that used the context definition

referred to by <cid>. <PDP_ address> is omitted if none is

available.

Reference

GSM07.07

Note

This Command dictates the behavior of PPP in the ME but not that of any

other GPRS-enabled foreground layer, e.g. browser.

5.2.8 AT+CGCLASS GPRS Mobile Station Class

AT+CGCLASS GPRS Mobile Station Class

Test Command

AT+CGCLASS=

Response

+CGCLASS:

(list of supported <

class

>s)

Parameter

See Write Command

Read Command

AT+CGCLASS?

Response

+CGCLASS:

<class>

Quectel

Summary of Contents for M10






































































































































































Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands

Quectel M10, At Command Set

Search results

Summary of Contents for M10

Reviews:

Related manuals for M10

Brands by name

Popular brands