Prestige Excellence Installation And Maintenance Manual Download Page 64

Page: 64 / 114

Start-Up Procedures

Check Vent Piping and Combustion Air

Piping.

Check for gas-tight seal at every con-

nection and seam of the venting and

combustion air piping.

Venting system must be sealed gas-tight

to prevent flue gas spillage and potential

carbon monoxide emissions, which will

result in severe personal injury or death.

Check Gas Piping

Check around the unit for gas odor fol-

lowing the procedure outlined in this

manual on Page 55.

If any gas leaks are found or suspected,

shut the unit down immediately. Use a

gas detection device or bubble test to

locate the source of the gas leak and

repair at once. Do not operate the unit

until the leak is corrected. Failure to

comply with this procedure could result

in severe personal injury, death or sub-

stantial property damage.

Verify Flame Pattern and Combustion
1. Check the flame pattern through the

inspection port of the heat exchanger.

The flame should be blue and stable.

The flame should be the length of the

burner head openings.

The combustion testing and adjustments

must be performed by a qualified

installer, service agency or the gas suppli-

er. All combustion measurements must be

performed with calibrated equipment to

ensure proper reading and accuracy.

2. Test for CO2 or O2 and for CO during

high firing rate. The combustion read-

ings should be within the range listed in

Table 4.

The CO level should not

exceed 100 ppm when combustion is

correct.

Perform the following proce-

dure to manually place the burner into

high fire.

a. Press the round

INSTALLER

button.

Reference Fig. 31, page 38.

b. Enter the installer access code “054” by

using the

LEFT

and

RIGHT

buttons to

select a digit and the

and

DOWN

buttons to change the digit. Press the

button to enter the access code.

c. Press the

RIGHT

button to highlight

the Manual Operation icon

then

press the

button.

d. Press the

button while the FAN

icon is highlighted to manually fire the

burner and power the CH circulator.

An adequate CH load must be present to

dissipate the heat generated during the

combustion test. If an adequate CH load

is not available, an indirect water heater

can be used to dissipate the heat by cre-

ating a DHW call which will enable the

DHW circulator.

WARNING

NOTICE

Manual Operation

Released

Off

CH1

FAN

DHW

SYS

CH2

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands