Prestige Excellence Installation And Maintenance Manual Download Page 29

Page: 29 / 114

Installing Vent/Combustion Air & Condensate Drain

SECTION V - Installing Vent /

Combustion Air & Condensate Drain

Installing Vent and Combustion Air

The PRESTIGE Excellence must be vent-

ed and supplied with combustion air as

shown in the PRESTIGE Vent

Supplement, included in the boiler instal-

lation envelope. Refer to optional vent kit

instructions for additional vent installa-

tion instructions. Once installation is

completed, inspect the vent and combus-

tion air system thoroughly to ensure sys-

tems are airtight and comply with the

instructions given in the venting supple-

ment and are within all requirements of

applicable codes. Failure to comply with

the installation requirements on the vent-

ing and combustion air piping will cause

severe personal injury or death.

Installing Condensate Drain Assembly

1. Locate the condensate drain assembly and

install as shown in Fig. 14 page 23.

2. Remove the retaining nut, metal washer

and rubber seals from the condensate drain

assembly. The metal washer must first be

cut using a pair of diagonal cutting pliers to

make it into a split washer. Insert the

metal washer into the retaining nut and

screw onto the condensate drain assembly

without rubber gaskets. Use the condensate

drain assembly as a tool to press the retain-

ing nut with metal washer onto the

polypropylene condensate pan.

The installer may want to fill the con-

densate trap with water prior to assem-

bling on the unit.

3. Reassemble the condensate drain assembly

onto the boiler by tightening the retaining

nut with rubber seal onto the boiler.

Ensure installation of the condensate

drain assembly included the metal wash-

er. Failure to comply could result in the

trap assembly dislocating from the boiler.

Ensure the condensate drain assembly

contains the plastic seated ball. Do not

install the condensate drain assembly if

the ball is lost or missing, replace the

entire assembly.

4. Remove the compression nut and rubber

seal from the drain outlet.

5. Using 3/4” x 2’ flexible PVC tube provid-

ed, slide the compression nut and rubber

seal over the pipe

The use of 3/4” PVC or CPVC pipe is

also acceptable. If 3/4” pipe is used

deburr and chamfer pipe to allow mat-

ing onto the drain assembly.

6. Thread the rubber seal into the compres-

sion nut to ease installation of the pipe to

the drain assembly.

7. Seat the pipe onto the drain assembly and

tighten the compression nut.

Hand tight

only!

The installer may opt to using 13/16" ID

tubing in lieu of rigid piping.

DANGER

WARNING

NOTICE

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands