Prestige Excellence Installation And Maintenance Manual Download Page 114

Page: 114 / 114

Additional quality water heating equipment available from:

ACV-

Triangle Tube

TTP Brazed Plate Heat Exchangers

- For domestic water, snow melting, radiant floor,

refrigeration

- Plates made of stainless steel, with a 99.9 % copper

and brazed, ensuring a high resistance to corrosion

- Self cleaning and self descaling

- Computerized sizing available from ACV- Triangle

Tube

- Available in capacities from 25,000 BTU/hr to

5,000,000 BTU/hr

- UL Listed

- Construction of high quality corrosion resistant

stainless steel (AISI 316)

- Specially designed built-in flow restrictor to assure

maximum heat exchange

- Compact and light weight

- Available in 8 sizes that can accommodate any size

pool or spa

Maxi-flo Pool and Spa Heat Exchangers

Triangle Tube - 1 Triangle Lane - Blackwood, NJ 08012 (856) 228 8881 Fax (856) 228 3584

www.triangletube.com / [email protected].

- Exclusive Tank-in-Tank design

- Stainless steel construction

- Available in 7 sizes

- Limited LIFETIME residential warranty

- 6 year limited commercial warranty

- Self cleaning/self descaling design

Smart Indirect Fired Water Heaters

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands