Prestige Excellence Installation And Maintenance Manual Download Page 2

Page: 2 / 114

This manual outlines the requirements for installation of the PRESTIGE Excellence.

Those requirements include Boiler Piping, Venting/Combustion Air, Start-Up and

Maintenance.

- For detailed instructions regarding the installation of the vent/combustion air system

reference the PRESTIGE Vent Supplement and/or the various optional vent kit

instructions.

- For instructions regarding the PRESTIGE Excellence Domestic Water Heater

Installation requirements and piping, reference the PRESTIGE Excellence Indirect

Water Heater Manual beginning after page 82 of PRESTIGE Excellence Water

Boiler Manual.

The PRESTIGE Vent Supplement is included in the unit’s installation envelope. For

instructions or information regarding the various optional vent kits contact ACV-

Triangle Tube Technical Support.

WARNING

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands