Prestige Excellence Installation And Maintenance Manual Download Page 52

Page: 52 / 114

Trimax Operation

Navigation: Home Screen>Main Menu>EZ Setup>DHW EZ Setup

Domestic Hot Water EZ Setup allows the installer to quickly customize the

domestic hot water settings for the application.

Select DHW Demand

Default: Sensor

Select DHW Demand prompts the installer to select the type of device which

will generate a DHW call. Press the

DOWN

buttons to select the

DHW Demand type then press the

button to store the setting. The Select

DHW Demand options are:
•

Switch

– A domestic hot water call from an aquastat or dry contact

switch will enable the Prestige with a fixed setpoint for a domestic hot

water call.

•

Sensor

– The Prestige Excellence utilizes an Indirect Water Heater

Sensor. The Prestige will monitor the DHW storage temperature and

generate a domestic hot water call when the temperature drops below

the DHW Storage Setpoint by 6ºF [3ºC].

DHW Storage Setpoint

Default: 140°F [60°C]

DHW Storage Setpoint prompts the installer to enter the domestic hot water

storage setpoint temperature when the Sensor option is chosen in Select

DHW Demand. Press the

LEFT

RIGHT

buttons to adjust the DHW

Storage Setpoint then press the

button to store the setting.

The Boiler DHW Setpoint will automatically be set 46°F [25°C]

higher than the DHW Storage Setpoint setting.

DHW Priority Timeout

Default: Off

DHW Priority Timeout prompts the installer to enter an optional time limit

that a domestic hot water call has priority over a central heating call. Press

the

LEFT

RIGHT

buttons to adjust the DHW Priority Timeout then press

the

button to store the setting.

NOTICE

Domestic Hot Water EZ Setup

Select DHW Demand

Switch

Sensor

68ºF

150ºF

140ºF

DHW

Storage Setpoint

Off

120 min.

Off

DHW Priority Timeout

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands