Prestige Excellence Installation And Maintenance Manual Download Page 94

Page: 94 / 114

Pre-Installation

In hard water areas (more than 7 grains of

hardness) soften the cold domestic supply

water to the appliance to prevent scaling.

Any water conditioning system must be

installed and maintained in accordance with

manufacturer’s specifications.

Do not install the Excellence water heater on

any application if the boiler piping contains

non-oxygen barrier tubing or if the boiler

piping is considered an “open system”.

Exposing the outer tank of the Excellence

water heater to oxygen contamination will

lead to premature tank failure and denial of

the warranty.

Locating Water Heater

• The Excellence is not intended for outdoor

installations.

• Locate Excellence so that any leakage from the

tank or water connections will not cause dam-

age to the area adjoining the water heater or to

lower floors in the structure.

Recommended Clearances

The Excellence is approved for zero clearance to

combustibles, excluding vent and boiler piping.

- Vent & Boiler Piping - 1/4 inch from com-

bustible materials.

To provide serviceability to the unit it is rec-

ommended that the following clearances be

maintained:

Top boiler jacket - 24 inches.
Front  - 24 inches.
Bottom boiler piping  - 24 inches.
Rear - 0 inches
Sides  - 6 inches

When maintaining zero clearance or less

than recommended clearances, some prod-

uct labeling may become hidden and

unreadable

When installing the Excellence in a confined

space, sufficient air must be provided for

proper combustion and venting and to

allow, under normal operating conditions,

proper air flow around the product to main-

tain ambient temperatures within safe limits

to comply with the National Fuel Gas Code

NFPA 54 - latest edition. Reference the

Excellence Boiler Manual for additional

guidelines.

Residential Garage Installations

When installing the Excellence in a residential

garage, the following special precautions per NFPA

54/ANSI Z223.1 must be taken:

- Mount the unit with a minimum 18 inches

above the floor level of the garage. Ensure

the burner and ignition devices / controls

are no less than 18 inches above the floor

level.

- Locate or protect the unit in a matter so it

cannot be damaged by a moving vehicle.

WARNING

NOTICE

BEST PRACTICE

NOTICE

BEST PRACTICE

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands