Prestige Excellence Installation And Maintenance Manual Download Page 53

Page: 53 / 114

Trimax Operation

Navigation: Home Screen>Main Menu>EZ Setup>EZ Setup Reset

EZ Setup Reset allows the installer to reset all EZ Setup settings back to

the original factory defaults. Follow the on screen instructions to reset all

EZ Setup settings back to the original factory defaults.

The EZ Setup Reset function will set Select DHW Demand to

Switch. Use Domestic Hot Water EZ Setup to change back to a sen-

sor demand.

Navigation: Home Screen>Main Menu>EZ Setup>Display EZ Setup

Display EZ Setup allows the installer to select the type of temperature

units displayed as well as the language used for all text. Press the

DOWN

buttons to select then press the

button to store the setting.

NOTICE

EZ Setup Reset

EZ Setup Reset

Press OK button

to restore factory settings.

Any other button

to keep current settings.

Display EZ Setup

Select Units

Fahrenheit

Celsius

Fahrenheit

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands