Prestige Excellence Installation And Maintenance Manual Download Page 80

Page: 80 / 114

Replacement Parts

Fig. 33: PRESTIGE Excellence Jacket Components

Item

Part #

Description

PTJKT11R

Rear Panel

PTJKT09F

Front Jacket Panel

PTRKIT129

Control Enclosure Bezel

PTJKT23S

Side Jacket Panel (Left or Right)

PTJKT15T

Top Jacket Panel

PTJKT19T

Top Jacket Panel - Blower Access

PEJKT03T

Top Jacket Panel - IDWH Access

PSRKIT21

Wall Mounting Bracket with Hardware

PTJKTSUP03

Support - Boiler Return Piping

Replacement parts must be purchased

through a local ACV-Triangle Tube dis-

tributor. When ordering part please pro-

vide the model number and description

and/or part number of replacement part.

Use only genuine ACV-Triangle Tube

replacement parts to ensure warranty

coverage and to avoid damage to appli-

ance and improper operation of appli-

ance. Contact ACV-Triangle Tube at

856-228-8881 or www.triangletube.com

for list of distributors nearest you.

WARNING

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands