Prestige Excellence Installation And Maintenance Manual Download Page 70

Page: 70 / 114

External Modulating Control

Factory Trimax Setting

Note 1: The Installer Reset function will set Prestige Model to Solo. Prestige Model must be changed back

to Excellence in Boiler settings.

Note 2: The Installer & EZ Setup Reset functions will set DHW Demand to switch. Use Domestic Hot

Water EZ Setup to change back to a sensor demand.

HEATING SETTING

FACTORY DEFAULT

EZ SETUP RESET INSTALLER RESET

Heating Operation

Enabled

Demand

Switch & Outdoor Reset

Absolute Max CH Setpoint

188°F [87°C]

CH1 Maximum Setpoint

180°F [82°C]

CH1 Minimum Setpoint

120°F [49°C]

Reset Curve Coldest Day

0°F [-18°C]

Reset Curve Warmest Day

64°F [18°C]

CH2 Circuit

Enabled

CH2 Maximum Setpoint

140°F 60°C]

CH2 Minimum Setpoint

80°F [27°C]

Warm Weather Shutdown

OFF

Pump Constant Circulation

Disabled

CH Post Pump Time

1 minute

Freeze Protection

Enabled

Frost Protection Setpoint

-22°F [-30°C]

Parallel Shift Value

0°F [0°C]

CH Call Blocking

1 minute

System Pump

CH1/CH2

DOMESTIC SETTING

FACTORY DEFAULT EZ SETUP RESET INSTALLER RESET

DHW Operation

Enabled

Demand (Note 2)

Sensor

Boiler DHW Setpoint

186°F [86°C]

DHW Storage Setpoint

140°F [60°C]

DHW On Differential

6°F [3°C]

DHW Storage Adder

46°F [25°C]

DHW Post Pump Time

1 minute

DHW Priority Timeout

OFF

DHW Priority

Enabled

DHW Call Blocking

0 minute

DHW to CH Call Blocking

1 minute

Antilegionella Function

Disabled

BOILER SETTING

FACTORY DEFAULT EZ SETUP RESET INSTALLER RESET

Prestige Model (Note 1)

Excellence

Lockout Temperature

210°F [99°C]

Modbus Address

0=BCST

Summary of Contents for Excellence



















































































































Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands

Prestige Excellence, Installation And Maintenance Manual

Search results

Summary of Contents for Excellence

Reviews:

Related manuals for Excellence

Brands by name

Popular brands