background image

Installation & Maintenance Manual for 
Camray 5 External Boilers

 

 

Heat is our Element 

Making the most of your energy1  

  

Manual Part No. PL61000 
Issue No. 2 
Date of Issue December 2003

  

Health & Safety 

INFORMATION FOR THE INSTALLER AND SERVICE ENGINEER. 

Under the Consumer Protection Act 1987 and the Health and Safety at Work Act 1974, it is a requirement to 
provide information on substances hazardous to health (COSHH Regulations 1988). 

The Company takes every reasonable care to ensure that these products are designed and constructed to 
meet these general safety requirements, when properly used and installed. 

To fulfil this requirement products are comprehensively tested and examined before dispatch. 

This appliance may contain some of the materials below. 

When working on the appliance it is the Users/Engineers responsibility to ensure that any necessary personal 
protective clothing or equipment is worn appropriate to parts that could be considered as being hazardous to 
health and safety. 

Page 1 of 40

Camray 5 External Boilers

14/04/2005

file://D:\PL61000\PL61000.htm

Summary of Contents for Camray 5









































Reviews: