Preiffer adixen ASM 380 Operating Instructions Manual Download Page 70

Page: 70 / 237

2/13

B 240

Accessories installation

GB 03659 - Edition 02 - March 12

Installation

Make sure brakes are activated (

E 650

)

Locate the fixing points of bottle rack.

Fix the bottle holder

with screws and bolts (kit 2).

Fix the suitable strap with screws and bolts (kit 1):

- the strap

for a bottle

145 mm/5.70 inches max.

- the strap

for a bottle

180 mm/7.08 inches max.

Strap fixing bottle Ø 180 mm/7.08 inches max

Strap fixing bottle Ø 145 mm/5.70 inches max

Bottle holder fixing

Bottle fixing

Bottles 180 mm/7.08 inches max can be used: use the suitable strap.

The maximum kit weight equipped with Helium bottle is 25 kg/55 Lbs.

adixen Vacuum Products - ASM 380 Operating instructions

Summary of Contents for adixen ASM 380














































































































































































































































Search results

Summary of Contents for adixen ASM 380

Reviews:

Preiffer adixen ASM 380, Operating Instructions Manual, Page: 70 / 237

Search results

Summary of Contents for adixen ASM 380

Reviews: