manualshive.com logo in svg

Potter UDACT-9100, Installation And Operation Manual, Page: 8 / 36

Share
Download
Potter UDACT-9100 Installation And Operation Manual Download Page 8

Mechanical Installation and Dimensions

4

Mechanical Installation and Dimensions

The 

UDACT-9100

 board is a single PCB assembly, which is a replacement for the UDACT-9000. Any reference

pertaining to the UDACT-9000 regarding mechanical mounting can be adhered to. Its mechanical installation is
determined by the Fire Alarm Control Panel (FACP) it will be installed in, and is described in the appropriate FACP
Installation Manual. Figure 1 below shows the mechanical installation for an PFC-5002 and PFC-5004 FACP.

Figure 1: UDACT-9100 Mechanical Installation

Notes:  

1. Front plate is not shown.
2. Reserved for PR-5000andUDACT9100
3. Other circuit adder modules may be:

• ZA-9008 Detection Circuit Adder Module
• IDC-9004 Signal Circuit Adder Module
• ARM-9008 Relay Circuit Adder Module
• SLA-127P SINGLE LOOP ADDER MODULE
• DLA-254P LOOP ADDER MODULE

UDACT-9100)

PR-5100)

MAIN CHASSIS
PFC-5002 and PFC-5004

firealarmresources.com

Summary of Contents for UDACT-9100





































Reviews:

No comments