Potter UDACT-9100 Installation And Operation Manual Download Page 29

Page: 29 / 36

UDACT-9100 Dialer Installation and Operation Instructions

SECURITY INDUSTRIES ASSOC. SIA-DCS

UDACT-9100 Internal Events:

UDACT-9100 External Events

* SIA protocol does not define indicating zone troubles, but lists it as Untyped Zone Trouble/Restore.

Event Description

Event Family

Qualifier

SIA Event
Code

Parameter

Phone Line #1 trouble detected

Trouble

New event

001

Phone Line #2 trouble detected

Trouble

New event

002

Phone Line #1 trouble restored

Trouble

Restore

001

Phone Line #2 trouble restored

Trouble

Restore

002

Failure to report to an Account

Trouble

New event

Acct #

Report to an Account successful

Trouble

Restore

Acct #

RS485 Communication Trouble

Trouble

New event

485

Periodic (24 hr) Test Event (Normal)

Test

New event

000

Periodic (24 hr) Test Event (Off-normal)

Test

New event

000

Manually initiated dialer test

Test

New event

000

Event Description

Event Family

Qualifier

SIA Event
Code

Parameter

Zone Fire Alarm

Alarm

New event

NNN

Zone Fire Alarm restored

Alarm

Restore

NNN

Zone Trouble detected

Trouble

New event

NNN

Zone Trouble restored

Trouble

Restore

NNN

Zone Supervisory condition

Supervisory

New event

NNN

Zone Supervisory restored

Supervisory

Restore

NNN

Waterflow alarm

Alarm

New event

NNN

Waterflow alarm restored

Alarm

Restore

NNN

General Alarm

Alarm

New event

NNN

General Alarm restored

Alarm

Restore

NNN

Indicating Zone Trouble (*)

Trouble

New event

NNN

Indicating Zone Trouble restored (*)

Trouble

Restore

NNN

AC power lost

Trouble

New event

000

AC power restored

Trouble

Restore

000

Battery Low

Trouble

New event

000

Battery Low restored

Trouble

Restore

000

Ground Fault

Trouble

New event

000

Ground Fault restored

Trouble

Restore

000

firealarmresources.com

Summary of Contents for UDACT-9100





































Search results

Summary of Contents for UDACT-9100

Reviews:

Potter UDACT-9100, Installation And Operation Manual, Page: 29 / 36

Search results

Summary of Contents for UDACT-9100

Reviews: