manualshive.com logo in svg

Potter UDACT-9100, Installation And Operation Manual, Page: 25 / 36

Share
Download
Potter UDACT-9100 Installation And Operation Manual Download Page 25

UDACT-9100 Dialer Installation and Operation Instructions

21

CommandMenu/Dialer-Config/Report Options

1.Alarm priority

[X] Account 1->Def

[ ] Account 2

Use this function to set 
the account priority for 
reporting alarms. If the 
priority is set for 
account#1 then the dialer 
will try account#1 first for 
reporting.

CommandMenu/Dialer-Config/Report Options

2.Trouble priority

[X] Account 1->Def

[ ] Account 2

Use this function to set 
the account priority for 
reporting trouble. If the 
priority is set for 
account#1 then the dialer 
will try account#1 first for 
reporting.

CommandMenu/Dialer-Config/Report Options

3.Supervisory priority

[X] Account 1->Def

[ ] Account 2

Use this function to set 
the account priority for 
reporting supervisory 
troubles. If the priority is 
set for account#1 then the 
dialer will try account#1 
first for reporting.

Command Menu/Dialer-Config/Report Options

4.Ignore Supervisory

[ ] ENABLE

[X] DISABLE->Default

If this function is enabled, 
the UDACT-9100 will 
bypass all supervisory 
event reporting. 

Command Menu/Dialer-Config/Report Options

5.Protocol type

[ ] Level 0

[X] Level 1

[ ] Level 2

[ ] Level 1-G

Change this function as 
required for appropriate 
fire alarm panel. Level 1 
is the PFC-5000.  Level 2 
is the PFC-9000 and 
Level 0 and 1-G are not 
used.

Command Menu/Dialer-Config/Report Options

6.Dialer operation mode

[X](U)DACT ->Default

[ ] DACT

Use this function to select 
the functionality of the 
dialer. In DACT mode 
only common trouble/
alarm/supervisory are 
reported, while in UDACT 
mode all zone point 
information is reported

Command Menu/Dialer-Config/Report Options

7.Checksum Bits

[X] 8 Bit->Default

[ ] 16 Bits

For PFC-5000 and     
PFC-9000, choose 8 Bits. 

16 Bits is not used.

A l a r m   P r i o r i t y :

[ X ]   A c c o u n t   1

T r o u b l e   P r i o r i t y :

[ X ]   A c c o u n t   1

S U P V   P r i o r i t y

[ X ]   A c c o u n t   1

Ignore Supervisory

[X] Disable

  Protocol:

 [X] Level 1

D i a l e r   O p e r .   M o d e :

[ X ]   ( U ) D A C T

 Checksum Bits:

[X] 8 Bits

firealarmresources.com

Summary of Contents for UDACT-9100





































Reviews:

No comments