manualshive.com logo in svg

Potter UDACT-9100, Installation And Operation Manual, Page: 13 / 36

Share
Download
Potter UDACT-9100 Installation And Operation Manual Download Page 13

UDACT-9100 Dialer Installation and Operation Instructions

9

Configuration Setup

T

here are 3 ways of configuring the UDACT-

9100

. 

1. Locally with the on-board keypad and CFG-LCD Configuration Tool.

2. Locally with a Personal Computer via the RS-232 connection, a UIMA and Potter Software MSW-012.

3. Remotely with a computer, modem and Potter Software MSW-012. 

CONFIGURATION VIA ON-BOARD KEYPAD:

1. Place jumper on JW2, located in the bottom right hand corner of the UDACT-9100 board (this will generate a 

trouble on the UDACT-9100 and report this to the receiver). 

2. Press Menu on the keypad to enter the configuration menu and configure the UDACT-9100. The following 

screen will ask for the passcode.

3. Enter the default passcode, 1111.

See next section entitled Configuration & LCD Operation for further instructions on Configuration.

CONFIGURATION VIA a UIMA AND COMPUTER(LOCAL):

1. Set-up UIMA connection: the 10-pin cable connector of UIMA is connected to P2 on UDACT-9100 board. A 

serial cable or USB cable is needed to connect the UIMA to the computer.

2. Place a jumper at JW2 on the UDACT-9100 board to allow the configuration (a trouble is generated and 

reported to the receiver DACR). 

3. Start the Potter Software MSW-012 on the computer to configure the UDACT-9100. Follow the instructions of 

MSW-012 menu to complete the configuration of the UDACT-9100.

4. Remove jumper on JW2 after configuration is finished, otherwise a trouble will occur.

CONFIGURATION VIA MODEM AND COMPUTER(REMOTE):

1. Set-up the modem connection on the computer. Make sure the phone line is working properly.

2. Place a jumper at JW2 on the UDACT-9100 board to allow the configuration (a trouble is generated and 

reported to the receiver DACR). 

3. Start the Potter Software MSW-012 on the computer to configure the UDACT-9100. Follow the instructions of 

MSW-012 menu to complete the configuration of the UDACT-9100.

4. Remove jumper on JW2 after configuration is finished, otherwise a trouble will occur.

Enter Passcode

Passcode:_

firealarmresources.com

Summary of Contents for UDACT-9100





































Reviews:

No comments