Polarstart PS-4660 TW Installation Manual Download Page 16

Page: 16 / 31

P. 16

Installation

Guide

PS-4660TW

Programming Options

MODE 1

* INDICATES DEFAULT SETTING

FUNCTION 1 – Ignition-controlled Door Locks

OPTION 1*

Ignition Lock

DISABLED

OPTION 2

Ignition Lock

ENABLED

OPTION 3

Ignition

UNLOCK ONLY

OPTION 4

Ignition

LOCK ONLY

FUNCTION 2 – Secure Lock

OPTION 1*

Secure Lock

DISABLED

(1-sec. Disarm pulse)

OPTION 2

Secure Lock

ENABLED

in Smart Secure Lock Mode

OPTION 3

Secure Lock

DISABLED

(1/2-sec. Disarm pulse)

OPTION 4

Secure Lock

ENABLED

in Standard Mode

OPTION 5

Secure Lock

(no rearm pulse when ignition and the ground out when running are ON)

FUNCTION 3 – Starter Kill Passive / Active Arming

OPTION 1*

PASSIVE

Arming (60 sec.)

OPTION 2

ACTIVE

Arming

OPTION 3

PASSIVE

Arming (3 min.)

FUNCTION 4 – Door lock pulse timing

OPTION 1*

7/10-sec. lock/unlock pulses

OPTION 2

4-sec. lock/unlock pulses

OPTION 3

7/10-sec. lock pulse and two 1/4-sec. unlock pulses

OPTION 4

1/10-sec. lock/unlock pulses

FUNCTION 5 – LED flashing

OPTION 1*

ENABLED

(without starter kill

will flash only when ignition is OFF)

OPTION 2

DISABLED

OPTION 3

ENABLED

(

with starter kill

will flash when the starter kill engages.

This option should be selected

ONLY

if the starter kill is installed.)

MODE 2

* INDICATES DEFAULT SETTING

FUNCTION 1 – Safe Start.

OPTION 1

Safe Start

ENABLED

OPTION 2*

Safe Start

DISABLED

OPTION 3

“Swap Start” – enhanced Safe Start Mode with extended safety:

To start the Engine: press the

SHIFT

button and then the

LOCK

button.

trigger

AUX 2

: press the

START/STOP

button.

Must have configured

option 1 or option 2 in mode 3 function 3.

FUNCTION 2 – Engine Run Time

OPTION 1

Run Time = 4 minutes in

GAS

mode / 9 minutes

DIESEL

mode

OPTION 2*

Run Time = 15 minutes in

GAS

mode / 20 minutes

DIESEL

mode

OPTION 3

Run Time = 25 minutes in

GAS

mode / 30 minutes

DIESEL

mode

FUNCTION 3 – Turbo Mode

OPTION 1

Turbo Mode

ENABLED

OPTION 2*

Turbo Mode

DISABLED

OPTION 3

Turbo Mode

ENABLED

FUNCTION 4 – Engine type and Cold Weather Mode

OPTION 1

30-sec delay diesel mode with 20-minute run time in cold weather mode

OPTION 2*

1-sec delay gas mode with 4-minute run time in cold weather mode

OPTION 3

7-sec delay diesel mode with 9-minute run time in cold weather mode

OPTION 4

15-sec delay diesel mode with 9 minute run time in cold weather mode

Summary of Contents for PS-4660 TW
































Search results

Summary of Contents for PS-4660 TW

Reviews:

Related manuals for PS-4660 TW

Brands by name

Popular brands

Polarstart PS-4660 TW, Installation Manual

Search results

Summary of Contents for PS-4660 TW

Reviews:

Related manuals for PS-4660 TW

Brands by name

Popular brands