Polaris Sportsman 9921825 Owner'S Manual Download | Manualshive

Page: 44 / 132

background image

41

OPERATION

Failure to operate the ATV properly can result in a collision, loss of control,
accident or overturn, which may result in serious injury or death. Read and
understand all safety warnings outlined in the safety section of this owner’s
manual.

Break-In Period

The break-in period for your new Polaris ATV is the first ten hours of
operation, or the time it takes to use the first two full tanks of gasoline.
No single action on your part is as important as following the proce-
dures for a proper break-in. Careful treatment of a new engine and drive
components will result in more efficient performance and longer life for
these components.

NOTICE:

Excessive heat build-up during the first three hours of operation will
damage close-fitted engine parts and drive components. Do not
operate at full throttle or high speeds during the first three hours of
use.

WARNING

«
...
42
43
44
45
46
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: KAYO MOTO Pages: 11

Brand: Bad Boy Pages: 56

Brand: Moni Pages: 27

Brand: Lynx Pages: 113

Stand-Up GO! Series

Brand: Kendon Pages: 40

Brand: Canyon Pages: 83

Brand: Can-Am Pages: 140

Brand: YSI Pages: 118

Brand: E-Z-GO Pages: 64

Brand: Land Pride Pages: 96

Raider mini 90S

Brand: Dazon Pages: 60

Brand: Yamaha Pages: 374

Brand: Twister Pages: 66

Brand: Rick's Specialty Vehicles Pages: 14

Brand: Rival Pages: 44

Brand: Outback Pages: 20

Brand: HOGG & DAVIS Pages: 64

Brand: HOGG & DAVIS Pages: 74

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands