background image

26

FEATURES AND CONTROLS

Throttle Lever

Operating an ATV with sticking or improperly operating throttle controls could 
cause an accident. Never start or operate an ATV that has a sticking or 
improperly operating throttle. Always contact your dealer for service before 
operating the vehicle.

Failure to check or maintain proper operation of the throttle system can result in 
an accident if the throttle lever sticks during operation. Always check the lever 
for free movement and return before starting the engine. Also check 
occasionally during operation.

Modifications to the electronic throttle control could result in failure to perform as 
designed, which could result in an accident. Do not attempt to modify the throttle 
control system or replace it with any after market throttle mechanisms. Always 
ensure that the throttle cable is installed and properly routed to the throttle 
control.

Engine speed and vehicle move-
ment are controlled by pressing the 
throttle lever. The throttle lever is 
spring loaded. Engine speed returns 
to idle when the lever is released.

This ATV is equipped with Polaris 
Electronic Throttle Control (ETC), 
which is designed to reduce the risk 
of a frozen or stuck throttle. If the 
throttle cable should stick in an 
open position when the operator releases the throttle lever, the engine 
will stop, and power to the rear wheels will cease.

WARNING

Summary of Contents for Sportsman 9921825





































































































































Reviews: