background image

15

SAFETY

Safety Warnings

Descending Hills Improperly

Improperly descending a hill could cause loss 
of control or overturn.
• Always follow proper procedures for travel-

ing down hills as described in the owner's 
manual. 

NOTE: 

A special technique is 

required when braking while traveling down-
hill. See page 53.

• Always descend a hill with the transmission 

in forward gear. Do not descend a hill with 
the transmission in neutral.

 

• Always check the terrain carefully before 

descending a hill.

• Shift your weight rearward.
• Never travel down a hill at high speed.
• Avoid traveling down a hill at an angle, which would cause the vehicle to lean 

sharply to one side. Travel straight down the hill when possible.

Crossing Hillsides

Driving on a sidehill is not recommended. 
Improper procedure could cause loss of control 
or overturn. Avoid crossing the side of any hill 
unless absolutely necessary. 
If crossing a hillside is unavoidable, always follow 
proper procedures as described in the owner's 
manual. See page 52.
Never attempt to turn the ATV around on any hill 
until you've mastered the turning technique (on 
level ground) as described in the owner's 
manual. See page 54.

Summary of Contents for Sportsman 9921825





































































































































Reviews: