Polaris Sportsman 9921825 Page 62 Owner'S Manual Download | Manualshive

Page: 62 / 132

background image

59

OPERATION

Hauling Cargo

Never exceed the weight capac-
ities specified for your ATV on
warning labels and in the speci-
fications section of this manual.

Cargo weight should be evenly
distributed (1/3 on the front
rack and 2/3 on the rear rack)
and mounted as low as possible.
When operating over rough or
hilly terrain, reduce speed and
cargo weight to maintain stable
driving conditions. Do not
obstruct the headlight beam
with cargo. Use low forward
gear when hauling or towing heavy cargo to extend belt life.

Towing Loads

Always attach a towed load to the hitch point. Remove the hitch from
the ATV when not towing a trailer. If towing a load, reduce rear rack
cargo weight by the amount of tongue weight.
• The combination of rear rack cargo weight and tongue weight must

not exceed the rear rack capacity.

• The total load (operator, accessories, cargo and weight on hitch) must

not exceed the maximum weight capacity of the vehicle.

NOTICE:

Using an improper hitch or exceeding
the maximum tongue weight capacity
can result in serious damage to the
vehicle and will void your ATV
warranty. Never install a hitch longer
than 4" (10 cm). Never install
automotive accessories on your
Polaris ATV. Always install Polaris-
approved (or equivalent) accessories
designed for ATV use.

1/3

2/3

Maximum

4" (10 cm)

«
...
60
61
62
63
64
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Polar Trailer 10537

Brand: Clam Pages: 7

Brand: Taylor-Dunn Pages: 244

Brand: SXT Pages: 40

Brand: Land Pride Pages: 132

Red Pedal Go Kart

Brand: Oypla Kids Pages: 5

Brand: PistenBully Pages: 20

Brand: VARES Pages: 44

Brand: Yamaha Pages: 158

Grizzly YFM600FWAM

Brand: Yamaha Pages: 164

Brand: Yamaha Pages: 182

Stand-Up TRIKE/SPYDER/SIDECAR Ride-Up SRL

Brand: Kendon Pages: 20

Brand: Arctic Cat Pages: 59

Brand: Arctic Cat Pages: 80

Brand: Arctic Cat Pages: 84

Brand: Arctic Cat Pages: 64

Brand: Arctic Cat Pages: 118

Brand: Arctic Cat Pages: 60

Brand: Arctic Cat Pages: 119

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands