Polaris Sportsman 9921825 Page 33 Owner'S Manual Download | Manualshive

Page: 33 / 132

background image

30

FEATURES AND CONTROLS

Auxiliary Foot Brake

Aggressively applying the auxiliary brake when backing down a hill may cause
rear tipover, which could result in serious injury or death. Never back down a hill.
Use caution when applying the auxiliary brake. Do not aggressively apply the
auxiliary brake when going forward. The rear wheels may skid and slide
sideways, causing loss of control, which may result in serious injury or death.

The auxiliary brake system is intended to be used as a backup for the
main brake system. Should the main system fail, use the auxiliary foot
brake. Since this is a rear brake only, it will not be as effective as the all-
wheel single lever system.

The auxiliary foot brake is located
on the inside of the right footrest.
Operate this brake with your right
foot.

If the rear wheels slide while using
the auxiliary brake,

reduce

brake

pedal pressure to brake the rear
wheels without skidding.

Brake Fluid Level

Check the brake fluid level frequently for the auxiliary brake system.
The reservoir is located near the auxiliary brake. Maintain the fluid level
between the maximum and minimum marks.

WARNING

Auxiliary Foot Brake

«
...
31
32
33
34
35
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: Lynx Pages: 75

Sportsman Forest 550

Brand: Polaris Pages: 146

Brand: J&M Pages: 27

Brand: Cub Cadet Pages: 28

Brand: Yerf-Dog Pages: 59

Brand: Suzuki Pages: 492

Brand: PRONAR Pages: 25

Brand: PRONAR Pages: 150

Brand: E-Z-GO Pages: 192

Brand: Yamaha Pages: 34

Brand: Palms Pages: 19

Brand: Moni Pages: 16

Quad Lander 250

Brand: Sym Pages: 223

Brand: Etnyre Pages: 64

Brand: Yamaha Pages: 172

Brand: Suzuki Pages: 33

Brand: Suzuki Pages: 146

Brand: Taylor-Dunn Pages: 204

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands