Polaris Sportsman 9921825 Page 109 Owner'S Manual Download | Manualshive

Page: 109 / 132

background image

106

MAINTENANCE

Cleaning and Storage

Washing the Vehicle

If a high pressure water system is used for cleaning (not recommended),
exercise extreme caution. The water may damage components and could
remove paint and decals. Avoid directing the water stream at the follow-
ing items:
• Wheel bearings
• Radiator
• Transmission seals
• Brakes
• Cab and body panels
• Electrical components
• Switches and controls
• Labels and decals

If an informational or graphic label becomes illegible or comes off, con-
tact your Polaris dealer to purchase a replacement. Replacement

safety

labels are provided by Polaris at no charge.

Grease all zerk fittings immediately after washing. Allow the engine to
run for a while to evaporate any water that may have entered the engine
or exhaust system.

Polishing the Vehicle

Polaris recommends the use of common household aerosol furniture
polish for polishing the finish on your Polaris vehicle. Follow the
instructions on the container.

Polishing Tips

• Avoid the use of automotive products, some of which can scratch the

finish of your vehicle.

• Always use clean cloths and pads for cleaning and polishing. Old or

reused cloths and pads may contain dirt particles that will scratch the
finish.

«
...
107
108
109
110
111
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: KAYO MOTOR Pages: 90

Pioneer SXS500M 2018

Brand: Honda Pages: 268

Brand: Yutrax Pages: 8

Brand: TrailMaster Pages: 8

Brand: TrailMaster Pages: 40

Brand: TrailMax Pages: 62

Brand: Can-Am Pages: 401

Brand: Axis Pages: 63

Brand: Axis Pages: 74

Brand: Can-Am Pages: 140

Brand: Kärcher Pages: 346

Brand: KAYO MOTOR Pages: 120

Brand: Can-Am Pages: 423

Brand: Yamaha Pages: 52

Brand: Suzuki Pages: 508

Brand: Taylor-Dunn Pages: 240

Brand: Yamaha Pages: 374

Brand: Schmeiser Pages: 28

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands