Polaris Sportsman 9921825 Page 93 Owner'S Manual Download

Page: 93 / 132

MAINTENANCE

Lights

Headlight Housing Replacement

1. Remove the two screws on the lower front corners of the headlight

pod.

2. Lift the pod slightly while depressing the tabs at the rear of the pod.

3. Lift the pod cover and disconnect the speedometer harnesses from

the speedometer.

4. Unplug the headlamp from the wiring harness.

5. Use a small screwdriver to remove the o-rings from the headlight

mounting tabs.

6. Pull the headlight housing up to release it from the locking tabs.

7. Lift the adjusting knob up to remove it from the locking tabs.

8. Carefully pull the assembly up

and out of the pod.

9. Reverse the steps to install the

new housing and reassemble
the pod. The distance from the
headlamp parting line to the
end of the adjustment knob
stop is 5 1/8" (13 cm).

10. Adjust the headlight aim by

turning the adjusting knob.

5 1/8"

(13 cm)

Summary of Contents for Sportsman 9921825





































































































































Search results

Summary of Contents for Sportsman 9921825

Reviews:

Related manuals for Sportsman 9921825

Brands by name

Popular brands

Polaris Sportsman 9921825, Owner'S Manual

Search results

Summary of Contents for Sportsman 9921825

Reviews:

Related manuals for Sportsman 9921825

Brands by name

Popular brands