Polaris Sportsman 9921825 Page 126 Owner'S Manual Download | Manualshive

Page: 126 / 132

background image

123

WARRANTY

WARRANTY COVERAGE AND EXCLUSIONS:
LIMITATIONS OF WARRANTIES AND REMEDIES

The Polaris limited warranty excludes any failures that are not caused by a defect in
material or workmanship. This warranty does not cover accidental damage, normal wear
and tear, abuse or improper handling. This warranty also does not cover any ATV that
has been altered structurally, modified, neglected, improperly maintained, used for rac-
ing, or used for purposes other than for which it was manufactured, or for any damages
which occur during trailer transit or as a result of unauthorized service or the use of
unauthorized parts. In addition, this warranty does not cover physical damage to paint or
finish, stress cracks, tearing or puncturing of upholstery material, corrosion, or defects in
parts, components or the ATV due to fire, explosions or any other cause beyond Polaris'
control.
This warranty does not cover the use of unauthorized lubricants, chemicals, or fuels that
are not compatible with the ATV. The exclusive remedy for breach of this warranty
shall be, at Polaris' exclusive option, repair or replacement of any defective materials, or
components or products. THE REMEDIES SET FORTH IN THIS WARRANTY ARE
THE ONLY REMEDIES AVAILABLE TO ANY PERSON FOR BREACH OF THIS
WARRANTY. POLARIS SHALL HAVE NO LIABILITY TO ANY PERSON FOR
INCIDENTAL, CONSEQUENTIAL OR SPECIAL DAMAGES OF ANY DESCRIP-
TION, WHETHER ARISING OUT OF EXPRESS OR IMPLIED WARRANTY OR
ANY OTHER CONTRACT, NEGLIGENCE, OR OTHER TORT OR OTHERWISE.
Some states do not permit the exclusion or limitation of incidental or consequential
damages or implied warranties, so the above limitations or exclusions may not apply to
you if inconsistent with controlling state law.

«
...
124
125
126
127
128
...
»

Summary of Contents for Sportsman 9921825





































































































































Reviews:

No comments

Related manuals for Sportsman 9921825

Brand: Husqvarna Pages: 64

Brand: Husqvarna Pages: 46

2008 HUV 4213-G

Brand: Husqvarna Pages: 52

Brand: Husqvarna Pages: 56

Brand: Husqvarna Pages: 60

Brand: Husqvarna Pages: 68

Brand: Husqvarna Pages: 57

2007 HUV 4421-D

Brand: Husqvarna Pages: 64

Beast 1000 Series

Brand: BMS Pages: 114

Viper Jr. (RXL-40)

Brand: E-TON Pages: 23

Brand: Polaris Pages: 68

Brand: Jayco Pages: 104

Brand: Landoll Pages: 36

07390 Workman HDX-Auto

Brand: Toro Pages: 280

Challenger4 300

Brand: TrailMaster Pages: 15

Brand: TrailMax Pages: 58

Brand: TrailMax Pages: 75

Brand: TrailMax Pages: 76

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands